Class B RV Cover Installation Guide

This guide provides detailed instructions on how to install, remove, and care for your Class B RV cover. It includes a pre-installation checklist, step-by-step instructions, cleaning guidance, and answers to frequently asked questions. Contents

1. Package Contents

2. Pre-Installation Requirements

3. Installation Procedure

4. Removal Procedure

5. Cleaning Guidelines

6. Frequently Asked Questions (FAQs) Package Contents

● 1 x Class B RV Cover
● 1 x Storage Bag
● 4 x Rain Gutter Protectors
● 1 x Ladder Cap
● 1 x Repair Patch
● 1 x Weighted Buckles Bag

Pre-Installation Requirements

● Clean the RV: Ensure the RV is free of dirt, debris, and moisture. A clean surface prevents damage to both the RV and the cover.

● Inspect for Sharp Edges: Identify any sharp or protruding areas like mirrors, gutters, or awnings that could damage the cover. Use the provided rain gutter protectors and ladder cap to pad these areas before installing the cover.

Installation Procedure

1. Prepare the Cover - Unpack the RV cover on a clean, flat surface, such as a driveway or lawn. Unfasten any buckles or straps.

2. Position the Cover - Lay the cover flat with the roof section facing upwards. Locate the tag marked "FRONT" to identify the front of the cover.

3. Fold and Roll - Fold the sides of the cover toward the center of the roof section and roll it from the back to the front.

4. Move the Cover to the Roof - Place the rolled-up cover on the roof of your RV at the front. Depending on the size of your RV, you may require assistance for this step.

5. Unroll and Drape - Unroll the cover from the front to the back. Unfold the sides so that they drape down over the RV.

6. Adjust the Cover - Begin descending the ladder, securing the ladder cap as you go. Pull the cover down over the RV, ensuring it is centered and properly aligned.

7. Secure the Corners - Once the cover is properly positioned, secure the bottom corner straps. Adjust the straps at both ends of the RV to ensure a snug fit.

8. Fasten the Straps - Secure the remaining bottom and middle straps. Use the weighted buckle bag to easily pass the straps beneath the RV and fasten them securely.

9. Final Check - Verify that the cover is properly fitted, adjusted, and all straps are secured. Warnings

● Do not occupy the RV while the cover is installed.

● Do not run the RV engine while the cover is on.

● Avoid installing the cover in windy or slippery conditions.

● It is recommended to have two people for the installation to ensure safety and ease.

Removal Procedure

To remove the Class B RV Cover, reverse the installation steps:

1. Unfasten all straps.

2. Roll the cover from back to front.

3. Fold it neatly and store it in the provided storage bag. Important: Ensure the cover is dry before storing to avoid mildew damage.

Cleaning Guidelines

● Manual Cleaning Only: Install the cover and rinse with water. Use a cloth and multi-purpose cleaner for stubborn areas.

● Rinse and Dry: After cleaning, rinse the cover thoroughly and allow it to air-dry or use a towel to speed up the drying process.
Do Not:

● Use soap, bleach, fabric softeners, or ironing.

● Store the cover while wet.

6. Frequently Asked Questions (FAQs)

How do I measure my Class B RV?

● Length: Measure from the front to the rear, including any bumpers, spare tires, or ladders.

● Height: Measure from the highest point of the sidewall to the bottom of the frame. Be sure to include bubble height for Class B vans, measured from the top of the van to the natural roofline.

How can I identify the front of the cover?

● The cover has a white tag labeled "FRONT" to indicate the front section. In case the tag is missing, the same section will still be considered the front.

● What are the zippers on the cover for?

● The zippers provide access to various sections of the RV while covered. Some models include a rear zipper for additional access.

How do I install the ladder cap?

● Place the ladder cap over the ladder and secure it using the Velcro straps.This prevents damage to the cover from sharp edges.
How do I use the weighted buckle bag?

● Attach the buckle to the strap, fill the bag with rocks or sand, and use it to toss the straps under the RV for easy fastening.